Electrical

Electrical

Hazardous Energy Release Session Three 3-1 Two Basic Types Energy in motion is Kinetic Energy Radiant Thermal Electrical (Light) Mechanical

Energy that is stored is Potential Energy Coiled spring Raised weight Water behind a dam Snow pack Stretched rubber band 3-2

Hydraulic Force created by liquid under pressure Liquids cannot be compressed They transmit force to surrounding areas 3-3 Pneumatic Air hose may uncouple or a fitting

may fail Rapid expansion of air causes the hose to whip violently Can cause a hazardous situation Whip Check 3-4 -Auger SpinoffPotential or Kinetic?

Rotating Machinery Hazards created by rotating parts & high pressure hydraulics Stay away Rotating parts can snag lose clothing Failure of hydraulic hoses can cause injury 3-5

Electrical Voltage is form of pressure Electromagnetic pressure Qualified Electrical workers use Minimum Approach Distances for protection Wear protective clothing and personal protective equipment 3-6

Electrical Arc Release of stored energy Always identify Line of Fire before starting the task In an arc flash metal is liquefied and vaporized

Projected with large amounts of force At very high speeds 3-7 -Suspended Pole-Stowed AugerPotential or or Potential Kinetic? Kinetic? 2-4 -Electrical Arc FlashPotential or Kinetic? 2-4

-Suspended LoadPotential or Kinetic? 4-4 Summary Critical Questions: Are we or will we be placing ourselves in Harms Way? Are we or will we be placing someone else in Harms Way? What could hit me, us, or them? How are we going to eliminate or control the

hazard? Because our work is dynamic, Lineof-fire hazards are also dynamic Each persons position with respect to line-of-fire must constantly be assessed 3-11 Key Points-Session Three 1. Energy in motion is kinetic energy. a. True b. False

2. Voltage is an example of pressure. 3. a. True b. False An important part of job planning is to identify possible sources of stored energy and determining if workers may be injured if there is a release of that energy.

a. True b. False 4. During the job planning stage it is determined that workers may be exposed to hazardous energy sources, the best protection is to when possible, eliminate the hazard. a. True b.

False 3-12 Review 3-13

Recently Viewed Presentations

  • Creating FOSIF Rota George B. Pressly

    Creating FOSIF Rota George B. Pressly

    Coordination with other OSIS nodes once they were online . NOSIC . Became our merchant shipping expertise and data base. Served as our advocate, liaison, (and gopher) in Washington intelligence community . Provided them with operational info as well as...
  • Sustainable Management of Soil Nitrogen and Organic Matter in ...

    Sustainable Management of Soil Nitrogen and Organic Matter in ...

    Introduction. Nutrients tied up in CC biomass are released back into the soil beginning at termination (Ditsch and Alley 1991). Minimum- till, mechanical-kill systems for cover crops have proven to be cost efficient, all while improving soil organic matter and...
  • MENOG 18 Segment Routing  Rasoul Mesghali CCIE#34938  Vahid

    MENOG 18 Segment Routing Rasoul Mesghali CCIE#34938 Vahid

    MPLS "classic" (LDP and RSVP-TE) control-plane was too complex and lacked scalability. LDP is redundant to the IGP and that it is better to distribute labels bound to IGP signaled prefixes in the IGP itself rather than using an independent...
  • Student Financial Assistance Session 22 How Do I

    Student Financial Assistance Session 22 How Do I

    Session 22 Converting data from one source to another Using an MS-Access database tool, this session will show how to pass data in and out of EDExpress's Pell Payment Module.
  • DMAIC Stages and Deliverables Define Measure Analyze Improve

    DMAIC Stages and Deliverables Define Measure Analyze Improve

    Process flowchart (ideally a value stream map) Measurement system validation. Baseline performance (process capability) Critical Success Factors. Accurate baseline data available (if not, measure report-out may be delayed) ... Proof of bullet #1 is indisputable, and the team has the...
  • 7 TEKNOLOGI DAN MANAGEMEN ALAT BERAT PROYEK CIVIL

    7 TEKNOLOGI DAN MANAGEMEN ALAT BERAT PROYEK CIVIL

    Batching Plant merupakan alat yang berfungsi untuk mencampur atau memproduksi beton ready mix dalam produksi yang besar. Batching plant digunakan agar produksi beton ready mix tetap dalam kualitas yang baik, sesuai standar, nilai slump test dan strength-nya stabil sesuai yang...
  • Implementation of Virginia Crime Codes in Criminal Justice

    Implementation of Virginia Crime Codes in Criminal Justice

    Implementation of Virginia Crime Codes in Criminal Justice Data Systems Recording offense information in standardized way is important The manner in which offense information is recorded on criminal justice databases has important implications for those who rely on such data...
  • Professional Learning Communities - WordPress.com

    Professional Learning Communities - WordPress.com

    PLC Norms. Norms represent commitments developed by each team to guide members in working together. These are commitments NOT beliefs. They are to be reviewed at the beginning and end of each meeting